Beam Clamps

Fig. 62 Small Mouth Beam Clamp Designed to attach hanger rod to the top or bottom flange of a beam or bar joist where flange thickness does not exceed 5/8 of an inch. Empire Figure 62 - Small Mouth Beam Clamp Submittal (Sizes 3/8" -1/2") PDF Empire...

Fig. 159 Adjustable Rod Beam Clamp Designed to be used in the suspension of a hanger rod from an Ibeam. Recommended for flange widths from 4 inches minimum to 8 inches maximum. Empire Figure 159 Adjustable Rod Beam Clamp Submittal PDF

Fig. 61 Wide Mouth Beam Clamp Empire’s Fig. 61 Wide Mouth Beam Clamp is designed to attach hanger rod to the top or bottom flange of a beam or bar. Empire Figure 61 - Wide Mouth Beam Clamp Submittal (Sizes 3/8" -1/2") PDF Empire Figure 61 –...

Fig. 218 Malleable Iron Center Load Beam Clamp Designed for the suspension of a hanger rod from the center of an I-beam. The clamp accommodates flange widths of 2-3/8” - 7”. Flange thickness not to exceed .60 inches. Normally used in...

Fig. 21L Steel C-Clamp Empire’s 21 and 21L Steel C-Clamps are designed for attaching hanger rod to the bottom flange of a beam. Features the ribbed design for added strength. Hardened steel cup point set screw secures clamp to beam. Stainless steel...

1/4" Electro-Galvanized Beam Clamp Empire’s Fig. 60G 1/4″ Beam Clamp is designed to attach 1/4” hanger rod from metal beams, channel or angle iron. Empire Figure 60G 1/4" Electro-Galvanized Beam Clamp Submittal PDF

Fig. 63 Electrical Rod Support Clamp Empire’s Fig. 63 Electrical Rod Support Clamp is designed to attach hanger rod to beam or framework where thickness does not exceed 1/2 inch. Rod tap on front and back of clamp. Empire Figure 63 Electrical Rod...

Fig. 22R Plain Steel Retaining Strap Empire’s Fig. 22R Retaining Strap is designed for use with Fig. 61 Wide Mouth and Fig. 62 Small Mouth Beam Clamps. Add 2” minimum to flange width to determine length. Empire Figure 22R...

Fig. 153 Side Beam Clamp Designed for mounting to sides of wood beams using drive screws. Bottom hole is tapped for rod. Empire Figure 153 Side Beam Clamp Submittal PDF

133 Standard Duty Beam Clamp Clamp centers the load on beam to prevent distortion Note: Spacer is furnished for use with Fig. 290 weldless eye nuts. Spacer may be removed for use with Fig 278 eye rods. Plain or Hot-Dip Galvanized with Zinc Plated...

134 Heavy Duty Beam Clamp Clamp centers the load on beam to prevent distortion. Two half-clamps, pipe spacer and bolt with nut assembled. Note: Spacer is furnished for use with Fig. 290 weldless eye nuts. Spacer may be removed for use with Fig 278 eye...

14 Adjustable Side Beam Clamp Recommended for supporting pipe from the bottom flange of beams. Size 3/8" through 5/8" Plain or Zinc Plated Product Submittal / Data Sheet PDF Anvil Pipe Hangers & Supports Submittal Catalog PDF

226 Truss Bracket or installation on the top chord of a steel web joist. Web thickness must be between 3/16" and 3/8" thick. Joist must be between 5" and 7" wide. For installation with Anvil Fig 202, 206, 207, & 551 brackets Rod Size 1/2" Material...

86 C-Clamp w/ Set Screw & Lock Nut Recommended for attachment to “W” and “M” beams where thickness of flange Z does not exceed 0.75". When clamp is used with Fig. 89 retaining clip, flange thickness may not exceed 0.62"...

92 Universal C-type Clamp, Standard Throat Recommended for use under roof installations with bar joist type construction, or for attachment to the top or bottom flange of structural shapes where the vertical hanger rod is required to be offset from the...

93 Universal C-type Clamp Wide Throat Recommended for use under roof installations with bar joist type constructions, or for attachment to the top or bottom flange of structural shapes where the vertical hanger rod is required to be offset from the edge...

94 Wide Throat Top Beam Clamp The Anvil Wide Throat Top Beam Clamp has a ductile iron body with hardened steel cup point set screw and locknut. Clamps to bar joists or top flanges. UL Listed. Recommended for use under roof installations with bar joist...

95 C-Clamp w/ Locknut Designed for fastening flange of “W” and “M” beam. Bottom hole tapped to accommodate hanger rod. Plain or Zinc Plated Product Submittal / Data Sheet PDF Anvil Pipe Hangers & Supports Submittal Catalog...

FIG 218 Malleable Beam Clamp w/o Extension Recommended for attachment to structural steel. Use in conjunction with beams where beam widths are from 2-3/8" minimum to 7" maximum and flange thickness does not exceed 0.60". Click here if you need the...

Fig. 21R Retaining Strap - Plain Carbon Steel Empire’s 21R Retainting Strap is designed for use with figure FIG. 21, FIG. 21L (3/8”-3/4”) and FIG. 23L (3/8”and 1/2”) to eliminate movement of the beam...

Fig. 23L Malleable Iron C-Clamp With Locknut Empire’s 23L Malleable Iron C- Clamp is designed for attaching hanger rod to the bottom flange of a beam. Empire Figure 23L - Malleable Iron C-Clamp with Locknut Sumbittal PDF

3/8" Purlin Clamp w/Locknut Empire’s Fig. 24L Purlin Clamp is designed for attaching hanger rod to large-lip steel Purlin beams. Empire Figure 24L 3/8" Purlin Clamp Submittal PDF