Description
Global Cam & Groove Type DC Dust Cap
Global Cam & Groove Type DC Dust Cap provides a female cam-and-groove cap connection designed to cover a compatible male camlock adapter when the connection is not in use.
The Type DC configuration uses cam levers to secure the dust cap over a compatible male cam-and-groove adapter. A Nitrile/Buna rubber seal provides the sealing interface within the cap, while the cam lever design allows quick installation and removal without special tools.
Product Highlights
Female cam-and-groove dust cap for compatible male camlock adapters.
The Type DC design combines cam lever operation with a Nitrile/Buna rubber seal for quick connection and removal.
Technical Specifications
Type DC Connection Configuration
The Type DC dust cap fits over a compatible male cam-and-groove adapter. The cap's cam levers are pressed downward using normal hand pressure to secure the connection.
The male adapter slides into the dust cap and provides the mating surface for the Nitrile/Buna rubber seal and cam lever connection.
Cam & Groove Dust Cap Design
The Type DC configuration provides a female camlock dust cap designed to connect over a compatible male cam-and-groove adapter. The cap closes the adapter connection when it is not connected to another camlock component.
To make the connection, slide the male adapter into the dust cap and press the cam levers downward using normal hand pressure. The cam arms secure the cap around the mating adapter.
The cam lever design allows the Type DC dust cap to be installed without special coupling tools. Both cam levers are pressed downward to secure the cap to the mating adapter.
Uncoupling is equally simple. Lift the cam arms and remove the dust cap from the adapter when access to the connection is required.
The Type DC dust cap uses a Nitrile/Buna rubber seal at the cam-and-groove connection. The seal provides the sealing interface between the dust cap and the inserted male adapter.
Inspect the seal and mating surfaces before installation. The seal should be properly seated and in suitable condition before the dust cap is connected.
The Type DC dust cap is designed to cover a compatible male cam-and-groove adapter when the connection is not in use. Correct nominal size and mating compatibility should be confirmed before installation.
Cam-and-groove couplings should not be used for compressed air or steam service. Confirm the intended system requirements before using the dust cap.
Installation & Selection Considerations
Confirm the required Type DC configuration.
Verify the correct nominal cap size.
Confirm mating adapter compatibility.
Fully close both cam levers.
Inspect the Nitrile/Buna rubber seal.
Review the Cam & Groove product literature for additional information about Type DC dust caps, connection configurations, mating components, seals, and other cam-and-groove products.
Need Help Selecting a Type DC Dust Cap?
Our product specialists can help review your nominal size, mating cam-and-groove adapter, seal requirements, and intended service to help determine the appropriate Type DC dust cap for your application.
Frequently Asked Questions
What is a Type DC Dust Cap?
A Type DC is a female camlock dust cap designed to fit over a compatible male cam-and-groove adapter.
How does the Type DC dust cap connect?
Slide the compatible male adapter into the dust cap and press the cap's cam levers downward using normal hand pressure to secure the connection.
What seal is supplied with the Type DC dust cap?
The supplied product information identifies the seal as Nitrile/Buna rubber.
Are tools required to install the dust cap?
No. The cam-and-groove connection is designed for coupling and uncoupling using the cam levers without special tools.
How is the Type DC dust cap removed?
Lift the cam arms and remove the dust cap from the mating male adapter.
Can Type DC cam-and-groove components be used for compressed air or steam?
No. Cam-and-groove couplings should not be used for compressed air or steam service.
Important Ordering & Installation Notes
- Confirm the required Type DC configuration.
- Verify the correct nominal cap size.
- Confirm mating adapter compatibility.
- Inspect the Nitrile/Buna rubber seal.
- Inspect both cam levers before use.
- Insert the mating adapter completely.
- Close both cam levers securely.
- Inspect mating surfaces before installation.
- Confirm system requirements before use.
- Do not use for compressed air or steam.
