Dixon
3/4" W-Series Wingstyle Hydraulic Quick Disconnect Coupler
- SKU:
- NLDIX6WF6-B
- Availability:
- Limited quantity available.
- Weight:
- 2.00 LBS
Description
3/4" W-Series Wingstyle Hydraulic Quick Disconnect Coupler
3/4" W-Series Wingstyle Hydraulic Quick Disconnect Coupler provides a threaded hydraulic connection designed for systems where residual pressure may remain during coupling.
The Dixon 6WF6-B uses a brass body, 3/4"-14 female NPTF connection, nitrile seals, and a wingstyle coupling mechanism suited to demanding wet-line and hydraulic equipment applications.
Product Highlights
Dixon 6WF6-B is a 3/4" brass W-Series wingstyle hydraulic coupler with a 3/4"-14 female NPTF connection.
The threaded wingstyle design supports hydraulic connections where residual system pressure may be present.
Technical Specifications
Wingstyle Coupler x Female NPTF Configuration
The wingstyle coupling mechanism mechanically draws the compatible mating component into engagement and supports connection where residual hydraulic pressure may be present.
The threaded connection installs onto compatible male NPTF hose ends, piping, manifolds, valves, or hydraulic equipment.
W-Series Wingstyle Hydraulic Coupler Design
The W-Series is designed for hydraulic applications where residual pressure may remain in the line when the coupler must be connected. The threaded wingstyle arrangement provides mechanical leverage that helps draw the mating component into position.
This design is commonly used where conventional push-to-connect couplers may be difficult to engage under trapped pressure. Hydraulic power should still be relieved whenever system conditions and equipment procedures allow.
The 6WF6-B combines a 3/4" quick-disconnect body size with a 3/4"-14 female NPTF threaded equipment connection. This allows the coupler to install directly onto compatible male threaded hydraulic components.
Thread size and type should be confirmed before installation because other 3/4" W-Series models use different thread configurations. Verify the mating component rather than selecting only by the coupler body size.
Dixon manufactures the 6WF6-B from brass and specifies nitrile rubber seals. The brass body provides the primary coupling structure while the internal sealing components support hydraulic fluid containment during normal operation.
Inspect the seals, threaded connection, wing nut, and mating surfaces periodically for wear, contamination, or visible damage. Damaged sealing components should be replaced before the coupler is returned to service.
Dixon rates the 6WF6-B for a maximum operating pressure of 3,000 PSI and a burst pressure of 13,000 PSI. Published flow is 31 GPM at a 32 PSI pressure drop for this 3/4" body configuration.
The W-Series is widely used on dump-trailer wet-line systems and oil-field equipment. Dixon does not recommend the series for continuous hydraulic impulse applications, so operating conditions should be reviewed before installation.
Installation & Selection Considerations
Confirm Dixon part number 6WF6-B.
Verify the 3/4" body size.
Confirm 3/4"-14 female NPTF threads.
Inspect seals and wingstyle hardware.
Verify hydraulic pressure requirements.

Our product specialists can help review 6WF6-B compatibility, 3/4" body size, female NPTF connection, hydraulic pressure requirements, seal material, and mating W-Series components before you order.
Frequently Asked Questions
What size is the Dixon 6WF6-B?
Dixon specifies a 3/4" body size with a 3/4"-14 female NPTF threaded connection.
What material is the 6WF6-B made from?
Dixon specifies brass construction with nitrile rubber seals.
What is the maximum operating pressure?
Dixon rates the 6WF6-B for a maximum operating pressure of 3,000 PSI.
Can the W-Series connect under residual pressure?
Yes. Dixon designs the W-Series for applications where residual pressure may be present during coupling.
What applications commonly use this coupler?
Dixon identifies dump-trailer wet-line hydraulic systems and oil-field equipment as common W-Series applications.
Is the W-Series recommended for continuous hydraulic impulse service?
No. Dixon states that W-Series couplings are not recommended for continuous hydraulic impulse applications.
Important Ordering & Installation Notes
- Confirm Dixon part number 6WF6-B.
- Verify the 3/4" body size.
- Confirm female NPTF connection.
- Check nitrile seal compatibility.
- Verify mating W-Series components.
- Do not exceed 3,000 PSI working pressure.
- Relieve hydraulic pressure when possible.
- Keep sealing surfaces free of debris.
- Inspect wingstyle hardware before use.
- Avoid continuous hydraulic impulse service.