Braxton Harris

2" IPS Cast Brass Shower Drain w/ Stainless Strainer Designed for use with prefab/fiberglass shower stalls. Comes with 4-1/4″ OD snap-in stainless steel strainer. Fits 2″ Iron Pipe Threads. A gasket can be used to make a no-caulk connection...

2" x 3" PVC Flush Fit Cleanout w/ 2" PVC Plug Fits over 2″ or inside 3″ schedule 40 DWV pipe. With built in stop.

2" x 60 Lbs Pressure Gauge, 1 lb Increments 2″ Face 1/4 MIP Brass Lower Connection Steel Case Shatterproof Face. May Be Used With Air Water Oil Gas Or Any Other Medium Not Corrosive To Brass.  

2-1/2" IPS Long Galvanized Compression (Dresser) Coupling 2-1/2" IPS GALVANIZED COMPRESSION (DRESSER) COUPLING. MADE OF MALLEABLE IRON. 125 PSI 120 DEGREES FAHRENHEIT. COMES WITH RUBBER GASKETS & METAL WASHERS. ALL COMPRESSION COUPLING MUST BE...

2-1/2" x 30 Lbs Pressure Gauge, 1/2 lb Increments 2 -1/2″ Face 1/4 MIP Brass Lower Connection Steel Case Shatterproof Face. May Be Used With Air Water Oil Gas Or Any Other Medium Not Corrosive To Brass.  

200lb Water/ Gas Test Gauge Assembly (3/4" mpt/ fght) 3/4″ male pipe threads or adapts to 3/4″ male hose threads. 2″ face with 1/4″ MPT adapter.  

276' 7/8" ID x 3/8" Wall Self Seal Pipe Insulation, 46 Per Carton 7/8" ID x 3/8" Wall Thickness. 6 Foot Lengths. Fits 3/4" CTS. R Factor: 2.2. Flame Spread Rating & Smoke Rating: 25/50. Will Not Contribute Significantly To Fire. Thermal Conductivity - ...

3" (C X FPT) WROT FEMALE ADAPTER 3″ COPPER SWEAT X 3″ FEMALE PIPE THREADS. WROT COPPER.  

3" (CXC) Wrot 45 Degree Elbow 3" Copper Sweat X 3" Copper Sweat "“ Wrot Copper "“ IAPMO Approved "“ NSF Approved

3" (CXC) Wrot Copper 90 Degree Elbow 3" Copper Sweat X 3" Copper Sweat "“ Wrot Copper "“ IAPMO Approved "“ NSF Approved

3" Cast Iron Cleanout w/ 2-1/2" Raised Head Brass Plug STANDARD BODY CLEANOUT (PLAIN END). FITS 3″ PIPE SIZE. 2-1/2″ RAISED HEAD SOUTHERN CODE PLUG SIZE. FOR SERVICE WEIGHT OR NO-HUB.

3" DWV Push-in PVC Repair Flange w/ Compression O-ring Joint REPLACES BROKEN CAST IRON CLOSET FLANGE, SLIDES INSIDE PIPE – FITS CAST IRON AND SCHEDULE 30 AND 40 PVC AND ABS

3" Hub PVC Floor Sink w/ 3/4" Grate Dome Strainer

3" IPS PVC Raised Head Cleanout Plug

3" MPT Drum Trap Cover FITS 3″ MALE PIPE THREADS. 4″ FLANGED DIAMETER. CHROME PLATED ZINC DIE CAST. FLANGED WITH GASKET

3" Pneumatic Clean-out Test Tee Plug Designed for testing plumbing lines above the cleanout tee. Design of plug will allow for passing of test water or air by deflating the plug. Threads directly into test tee. Threads into both cast iron and plastic...

3" PVC Deep Techno Test Plug Cap Fits 3" DWV. Heavy duty PVC. Pressure tested to over six stories. Deep design is easily glued over end of DWV pipe and helps adequately cover unevenly cut pipe. Diameter prevents cover from falling in pipe.

3" PVC Plastic Roof Drain w/ Cast Iron Dome FITS OVER 3″ SCHEDULE 40 DWV PIPE. WITH GRAVEL GUARD AND CAST IRON DOME. THREADED BRASS INSERTS FOR ATTACHING UNDER DECK CLAMP. CAN BE TAPPED FOR TRAP PRIMER. DOME FILL AREA IS 50 SQUARE INCHES.  

3" Triple Seal Tank Ball 3″ TRIPLE SEAL TANK BALL  

3" X 1-1/2" (CXC) Wrot Reducer Coupling 3" Copper Sweat X 1-1/2" Copper Sweat "“ Wrot Copper "“ IAPMO Approved "“ NSF Approved

3/16" BARB X 1/8" MPT BRASS HOSE BARB ADAPTER 3/16" BARB (HOSE ID) X 1/8" MALE PIPE THREADS

3/4" MHT X 1/2" MPT X 1/2" SWT Brass Hose Nipple 3/4″ MALE HOSE THREAD X 1/2″ MALE PIPE THREAD X 1/2″ FEMALE SWEAT BRASS GARDEN HOSE FITTING  

3/4" x 3/4" MIP Poly Insert Male Adapter Elbow Made of Polypropylene. Meets ASTM D2609. Insert fittings join to PE (Polyethylene) pipe with stainless steel clamps.. Cold water use only.

3/4" x 60 PSI Bell Gas Test Gauge Assembly W/ BELL TYPE HOUSING  

3/8" Barb x 1/4" MPT Brass Hose Barb Adapter 3/8" BARB (HOSE ID) X 1/4" MALE PIPE THREADS

3/8" FIP x 3/8" MIP x 60" L Poly Coated Gas Connector (3/8" OD Hose) Made of yellow poly coated 304 stainless steel 3/8" OD (1/4" ID) corrugated hose. Zinc plated fittings to prevent corrosion. CSA certifified. Quality machined fittings to ensure leak...

3/8" Flare Brass Cap 3/8" flare threads. Used with copper, brass, aluminum, welded steel tubing. Used on lines handling hard to hold liquids and gases, including gasoline, grease oil, water, vacuum lines, air lines, LP and natural gasolines,...

3/8" FPT Brass Full Port Ball Valve- Lead Free 3/8″ X 3/8″ FEMALE PIPE THREADS. 400 PSI WATER, OIL, GAS. 150 PSI WORKING STEAM PRESSURE. HARD CHROME PLATED BRASS BALL. QUARTER TURN OPERATION. DACROMET PLATED STEEL HANDLES WITH VINYL GRIP AND...

3/8" OD x 1/2" FIP 24" Length S.S. Faucet Connector- Lead Free 24" length, 3/8" OD compression x 1/2" female pipe threads. High quality stainless steel braid increases pressure burst rating to 1,000 PSI and and helps to prevent creasing or kinking...

3500W 240V Screw-in Element for Water Heater “S” MODEL ELEMENTS- THREADED, 3500 WATT (HIGH DENSITY), 240 VOLT, TANK DIAMETER 12″. COMES WITH RUBBER GASKET

4 -1/4" OD Strainer w/ 3-3/8" Screw Holes- Oil Rubbed Bronze 4-1/4" Outside Diameter. 3-3/8" Screw hole to Screw hole centers. Comes w/ finished screws.

4" (CXC) Wrot 45 Degree Elbow 4" Copper Sweat X 4" Copper Sweat "“ Wrot Copper "“ IAPMO Approved "“ NSF Approved

4" - 6" Inflatable Water/ Air Test Plug FITS 4″, 5″ AND 6″ PIPES. FOR PRESSURE TESTING DRAIN LINES. USER SAFE: PRE-SET PRESSURE RELIEF VALVE PREVENTS OVER-INFLATION. HOLDING POWER: MULTI-RIBBED BODY CREATES TIGHT EFFECTIVE SEAL...

4" Brass Closet Flange (1-1/8" Deep seal) 4″ pipe size. Deep seal brass. For lead connection

4" Cast Iron No Hub Cleanout w/ 3-1/2" Heavy CS Brass Plug 4″ CAST IRON NO HUB CLEANOUTS W/ 3-1/2″ C.S. HEAVY BRASS PLUGS-NO HUB CLEANOUT. FITS 4″ PIPE SIZE. 3-1/2″ COUNTERSUNK HEAVY PATTERN PLUG SIZE.

4" Flexible Saddle Tee w/ S.S. Series 300 Clamps THESE FLEXIBLE SADDLES DEMONSTRATE SUPERIOR FLEXIBILITY IN MORE THAN ONE WAY. THE SADDLES ELASTOMERIC CONSTRUCTION ALLOWS A SINGLE SIZE TO SECURELY FIT 6″ THROUGH 12″ PIPE DIAMETERS. THE...

4" IPS Flange Connection Kit w/ Asbestos Free Full Face Gasket FITS 4" IRON PIPE. BOLT SIZE: 5/8" DIAMETER X 3" LENGTH. KIT INCLUDES: 8 BOLTS, 8 NUTS, 1 ASBESTOS FREE FULL FACE GASKET. HEX BOLTS AND NUTS MEET ASTM A307. GASKETS MEET ASTM F152, F36A,...

4" PVC Ball Valve- Solvent Weld ONE PIECE CONSTRUCTION. EPDM SEATS. EPDM O-RINGS. SUITABLE FOR SWIMMING POOLS. 1/4 TURN OPERATION. RATED AT 150 PSI. SOLVENT ENDS COMPLY WITH ASTM D2466. NOT FOR USE WITH COMPRESSED AIR.  

4" PVC Snap-in Cleanout w/ Threaded Brass Inserted 3-1/2" PVC Cleanout

4" Sch 40 PVC Backwater Valve Fits 4″ schedule 40 DWV pipe. Easy access threaded plastic cover with a positive seal elastomeric gasket. Non-corrosive flexible flapper provides seal against backflow. UPC, CSA AND SBCCI approved. Magnetic strip for...