Lesso America
ABS DWV 45 Reducing Street Wye (SPG x HUB x HUB)
- SKU:
- LN603
- Availability:
- Usually Ships Same Day
- Weight:
- 0.00 LBS
Description
ABS DWV 45 Reducing Street Wye (SPG x HUB x HUB)
ABS DWV 45 Reducing Street Wyes provide a smooth 45-degree branch connection with a street-style spigot end while also transitioning between different nominal pipe sizes.
Featuring a spigot (SPG) connection on the branch side and two hub connections on the main run, this fitting is designed for non-pressure ABS drain, waste, and vent systems that require both a gradual branch transition and a size reduction. The street-style spigot connection can fit directly into a compatible ABS DWV hub, while the reducing configuration can eliminate the need for an additional reducer in certain layouts. Manufactured for ABS DWV service, it meets recognized standards including ASTM D2661, CSA B181.1, and NSF Standard 14.
Product Highlights
- ABS DWV 45 reducing street wye
- SPG x HUB x HUB connection configuration
- Spigot connection on the branch side
- Two hub connections on the main run
- Provides a gradual 45-degree branch connection
- Transitions between different nominal pipe sizes
- Street-style branch can connect directly into a compatible ABS DWV hub
- Can reduce the need for an additional coupling
- Can reduce the need for a separate reducing fitting
- Supports efficient drainage flow
- Designed for solvent-cement installation
- Suitable for drain, waste, and vent systems
- Suitable for sewer and general drainage applications
- Non-pressure fitting
- Maximum operating temperature of 140°F
- Not intended for compressed air or gas service
- Not intended for pressure testing
- Manufactured from virgin ABS polymers
- Complies with ASTM D2661
- Certified to CSA B181.1
- Meets NSF Standard 14 requirements
Technical Specifications
| Product Type | ABS DWV 45 Reducing Street Wye |
|---|---|
| Material | ABS |
| Connection Type | Spigot (SPG) x Hub x Hub |
| Branch Connection | Spigot (SPG) |
| Main Run Connections | Hub x Hub |
| Branch Angle | 45 Degrees |
| Configuration | Reducing Street Wye |
| Number of Connections | 3 |
| Joint Method | Solvent Cement |
| System Type | Drain, Waste, and Vent (DWV) |
| Pressure Service | Non-Pressure |
| Maximum Operating Temperature | 140°F |
| Primary Function | Provide a 45-Degree Street-Style Branch Connection with a Pipe-Size Transition |
| Referenced Standards | ASTM D3965, ASTM D2661, CSA B181.1, NSF Standard 14 |
| Typical Applications | Sanitary Drainage, Waste Lines, Sewer Piping, General Drainage, and Reduced-Size Branch Connections |
Connection Configuration
Main Run Hubs
The two hub connections form the primary ABS DWV piping run and accept compatible ABS pipe for solvent-cement installation.
Reducing Street Branch
The branch uses a spigot connection and may be a different nominal size than the main run, depending on the specific fitting variation.
45 Reducing Street Wye Design
This fitting combines three useful functions in one molded ABS component: a 45-degree wye branch, a street-style spigot connection, and a pipe-size reduction.
The branch enters the main run at approximately 45 degrees to support smoother drainage flow, while the spigot end can connect directly into a compatible ABS DWV hub fitting.
The reducing configuration allows different pipe sizes to be connected within the same fitting, helping simplify compact or space-sensitive piping layouts.
Why Choose an ABS DWV 45 Reducing Street Wye?
Compact Reducing Branch
- Provides a gradual 45-degree branch entry
- Transitions between different pipe sizes
- Spigot branch fits directly into a compatible hub
- Can reduce the need for an extra coupling
- Can reduce the need for a separate reducer
ABS DWV Benefits
- Lightweight construction
- Easy handling and installation
- Suitable for non-pressure drainage systems
- Compatible with ABS DWV piping systems
- Designed for long-term sanitary drainage service
Typical Applications
Drainage Systems
- Sanitary drain lines
- Waste piping
- Sewer piping
- General building drainage
- ABS DWV main runs
Reducing Street Connections
- Reduced-size branch drains
- Direct fitting-to-fitting connections
- Different-size DWV connections
- Residential plumbing
- Commercial drainage systems
Standards & Compliance
- ASTM D3965: ABS material requirements for pipe extrusion and molded fittings
- ASTM D2661: Schedule 40 ABS drain, waste, and vent pipe and fittings
- CSA B181.1: ABS drain, waste, and vent pipe, fittings, and accessories
- NSF Standard 14: Plastic piping system components and related materials
Installation
Verify all three connection sizes before installation and identify which connection provides the size reduction.
Cut all mating ABS pipe ends square and remove burrs. Clean and prepare the pipe, hub, spigot, and mating fitting surfaces according to accepted ABS solvent-cement installation procedures.
Dry-fit the complete assembly before applying solvent cement to confirm branch orientation, flow direction, proper size transition, and seating of the spigot into the mating hub.
Apply compatible ABS solvent cement as required. Fully seat the main-run pipe into each hub and the spigot branch into its compatible mating hub fitting while maintaining correct alignment.
Allow completed joints to cure according to the solvent cement manufacturer's recommendations before placing the drainage system into service.
Our piping specialists can help review your main-run size, branch size, reduction, street connection, and ABS DWV compatibility before you order.
Email the GetPipe.com Team Visit Quick SupportFrequently Asked Questions
What is an ABS DWV 45 reducing street wye used for?
It is used to create a gradual 45-degree branch connection while transitioning between different ABS DWV pipe sizes and providing a direct spigot-to-hub connection.
What does SPG x HUB x HUB mean?
It means the fitting has one spigot connection and two hub connections.
Which connection is the spigot end?
The supplied product information identifies the branch side as the spigot connection, with hub connections on the two main-run ends.
What makes this fitting reducing?
At least one connection is a different nominal size from another connection, allowing the fitting to transition between different ABS DWV pipe sizes.
What makes this a street wye?
The spigot branch can connect directly into a compatible hub fitting without requiring an additional coupling between fittings.
What angle does the branch enter the main run?
The branch enters at approximately 45 degrees.
Which connection is reduced?
The reduced connection depends on the specific size variation. Verify all listed connection sizes before ordering.
Does this fitting require solvent cement?
Yes. The hub and spigot connections are intended for compatible ABS solvent-cement installation.
Is this fitting intended for pressure systems?
No. This fitting is intended for non-pressure drain, waste, vent, sewer, and general drainage applications.
Can it be used for compressed air or gas?
No. The supplied product information states that ABS DWV fittings are not intended for transporting compressed air or gas.
What should I verify before ordering?
Confirm all three connection sizes, which connection is reduced, branch orientation, location of the spigot end, mating hub compatibility, and intended non-pressure ABS DWV application.
Important Ordering & Installation Notes
- This listing is for an ABS DWV 45 Reducing Street Wye with SPG x HUB x HUB connections.
- Verify all three nominal connection sizes before ordering.
- At least one connection differs in size from another connection.
- Confirm which connection provides the reduced-size transition.
- The supplied configuration places the spigot connection on the branch side.
- The two main-run connections are hub-style connections.
- The branch enters the main run at approximately 45 degrees.
- The spigot branch is designed to fit directly into a compatible ABS DWV hub fitting.
- The street-style connection can reduce the need for an additional coupling.
- The reducing configuration can reduce the need for a separate reducer.
- Confirm branch orientation, flow direction, and mating hub compatibility before installation.
- Dry-fit the complete assembly before applying solvent cement.
- This fitting is intended for non-pressure DWV, sewer, and general drainage applications.
- Do not use for transporting compressed air or gas.
- Do not use for pressure testing.
- Maximum operating temperature is 140°F.
- Use compatible ABS solvent cement for installation.
- Cut pipe square and remove burrs before assembly.
- Clean and prepare all mating pipe, hub, and spigot surfaces before solvent-cement installation.
- Fully seat each ABS pipe into its corresponding hub.
- Fully seat the spigot connection into the compatible mating hub.
- Maintain proper branch and flow alignment while the solvent-cement joints set.
- Allow completed joints to cure according to the solvent cement manufacturer's recommendations before service.
- Protect the fitting from incompatible chemicals, fire-stopping materials, thread sealants, and other aggressive agents that may damage ABS compounds.
- Consult manufacturer documentation for complete dimensions and available reducing configurations.
- Follow applicable plumbing codes and manufacturer installation recommendations.
