ASC

94 Wide Throat Top Beam Clamp The Anvil Wide Throat Top Beam Clamp has a ductile iron body with hardened steel cup point set screw and locknut. Clamps to bar joists or top flanges. UL Listed...

93 Universal C-type Clamp Wide Throat Recommended for use under roof installations with bar joist type constructions, or for attachment to the top or bottom flange of structural shapes where the...

92 Universal C-type Clamp, Standard Throat Recommended for use under roof installations with bar joist type construction, or for attachment to the top or bottom flange of structural shapes where the...

CT-121 Copper Tubing Riser Clamp Recommended for support and steadying of copper tube risers, either insulated or non-insulated. This product is not intended for use with hanger rods. For support and...

261 Extension Pipe or Riser Clamp For support of stationary steel pipe risers, cast iron pipe or conduit. This product is not intended for use with hanger rods. For this application refer to Fig. 40...

67 Pipe or Conduit Hanger Can be suspended by hanger rod or attached to wall. “T” slot in hanger permits side bolt to be installed after installation and setting of pipe. Strap and bolt...

CT-65 Light Adjustable Clevis Hanger Copper Plated Recommended for suspension of non-insulated, stationary copper tube. Adjustment may be made either before or after tubing is in place without...

65 Light Adjustable Clevis Hanger Recommended for suspension of stationary pipe or conduit. An economical attachment for light duty service. Product Submittal / Data Sheet PDF Anvil Pipe Hangers...

260 Adjustable Clevis Hanger Recommended for the suspension of stationary pipe lines. Design has yoke on outside of lower U-strap so yoke cannot slide toward center of bolt, thus bending of bolt is...

3205 Ductile Iron Straight Tee SCI Ductile Iron Pipe Fittings conform to ASME B16.3 dimensions. Bushings and couplings conform to ASM B16.14. The threads are NPT per ANSI/ASME B1.20.1. Ductile iron...

Clevis Hanger with Insulation Saddle System 260R ISS Recommended for the suspension of stationary insulated chilled or hotwater pipe lines.  V-Block design cradles pipe through out the entire...

Clevis Hanger with Insulation Saddle System 260 ISS Recommended for the suspension of stationary insulated chilled or hotwater pipe lines.  V-Block design cradles pipe through out the entire...

150# Galvanized Malleable Iron Reducing 90° Street Elbows Class 150 Malleable Iron Fittings conform to ASME B16.3 All elbows and tees 3/8" and larger are 100% gas tested at a minimum of 100 PSI...

Carbon Steel Press 45° Degree Street Elbows SCI Press Carbon steel Fittings are intended for use with ASTM A53 carbon steel piping, Sched 10 and 40, in sizes ¾" to 2”. Color-coded...

SS Compression Hex Nut Double Ferrule Instrumentation fittings meet ANSI B31.1, ANSI B31.3, ASME Sec. VIII Instrumentation fitting wall thickness conform to SAE-J-514 NPT pipe threads conform to...

Anti-Siphon Frost Free Sillcock MIP x Sweat 3/4" MHT outlet 1/2" MIP x 1/2" Sweat inlet Chrome plated brass body Vacuum breaker Metal handle (plastic handle available) IAPMO/UPC listed CSA approved...

Brass Gate Valve Lead Free Sweat California AB1953 lead-free approved Meets federal Safe Water Drinking Water Act, lead-free requirement 200LB CWP 125LB WSP Full Port (1/4-3) Cast Brass Non-rising...

125# Bronze Lead-Free Threaded 45° Elbows Bronze fittings conform to AWWA C800 Bronze castings manufactured from ASTM B584 UNS Alloy C89833 ingot Bronze fitting dimensions conform to ASME B16...

J-Hanger 1/2" through 4" NPS Electro-Galvanized Max Temperature: 450° F For the suspension of stationary pipe Max Load: 1/2" - 2-1/2" 150 lbs. Max Load: 3" 200 lbs. Max Load: 4" 250 lbs. Product...

Brass Hose Bibb MIP Inlet 125 lb. CWP NPT x 3/4" NHT Cast brass Heavy duty configuration Green tee handle Certified to NSF/ANSI 61-8 ISO 9001:2008 manufacturer Series 166 Brass No Kink Hose Bibb...

Boiler Drain with Stuffing Box FIP Inlet 125 lb. CWP Full Flow NPT x 3/4" NHT Cast Brass CSA Approved Certified to NSF/ANSI 61-8 ISO 9001:2008 manufacturer Series 102 & 103 Boiler Drain Stuffing...

Brass In-Line Check Valve Threaded California AB1953 lead-free approved Meets federal Safe Water Drinking Water Act, lead-free requirement Rated at 200 psi Cast brass Spring loaded Stainless steel...

150# Black Malleable Iron Reducing 90° Street Elbows Class 150 Malleable Iron Fittings conform to ASME B16.3 All elbows and tees 3/8" and larger are 100% gas tested at a minimum of 100 PSI Class...

3000# 316L Stainless Steel Threaded Tee Forged Stainless Steel Conforms to ASTM A-182 Grade F304/304L - F316/316L Forged Stainless Steel Fitting Dimensions Conform to ASME B16.11 NPT Threads Conform...

Schedule 10 316/L Stainless Steel Tee Stainless weld fittings conform to ASTM A403 Grade 316/316L CMTR's available upon request Stainless weld fitting dimensions conform to ASME B16.9 (except Wall)...

3000# 304L Stainless Steel Threaded Tee Forged Stainless Steel Conforms to ASTM A-182 Grade F304/304L - F316/316L Forged Stainless Steel Fitting Dimensions Conform to ASME B16.11 NPT Threads Conform...

3000# 316L Stainless Steel Socket Weld Tee Forged Stainless Steel Conforms to ASTM A-182 Grade F304/304L - F316/316L Forged Stainless Steel Fitting Dimensions Conform to ASME B16.11 NPT Threads...

3000# 304L Stainless Steel Socket Weld Tee Forged Stainless Steel Conforms to ASTM A-182 Grade F304/304L - F316/316L Forged Stainless Steel Fitting Dimensions Conform to ASME B16.11 NPT Threads...

SCI® Press - Copper 90° FPT Female Elbow Fig. SP698 SCI Copper Press fittings provide an economical and reliable piping connection that can be used for commercial, industrial, and residential...

150# Stainless Steel Threaded Cross - Grades 304 & 316 Class 150# Heavy Pattern  Stainless Castings: ASTM A-351 ACI Grade CF8 (304) & ACI Grade CF8M (316) NPT threads conform to ASME B1...

Stainless Steel Three Piece Full Port Threaded Ball Valve Full Port - 3PC Stainless Body Locking Device Handle Blowout Proof Stem RTFE Seat Max Pressure: 1000 CWP Catalog PDF Pipe Chart: Common...

Stainless Steel Sanitary Clamp End Short Weld Ferrule  Sanitary tubing and fittings are produced to 3-A Sanitary Standards Stainless steel sanitary tubing dimensions and materials conform to...

Schedule 40 Seamless Red Brass Nipple - Single Run 1ea Close thru 6" in 1/2" Increments Seamless brass pipe conforms to ASTM B43 Seamless red brass nipples conform to ASTM B687 NPT threads on...

Stainless Steel Sanitary Clamp End Reducing Tee Sanitary tubing and fittings are produced to 3-A Sanitary Standards Stainless steel sanitary tubing dimensions and materials conform to ASTM A269/A270...

Sch10 Stainless Steel Grooved Reducing Tee Gruvlok Stainless Steel, Full-Flow Grooved fittings are made of lightweight, corrosion-resistant Type 304 stainless steel. The assortment of available...

3358 Cast Iron Straight Tee Cast Iron Pipe Fittings conform to ASTM A126 Pipe fitting dimensions conform to ANSI B16.4 Class 125 The threads are NPT per ANSI/ASME B1.20.1 All Cast Iron Fittings are...

Stainless Steel Sanitary Long Weld End Tee Sanitary tubing and fittings are produced to 3-A Sanitary Standards Stainless steel sanitary tubing dimensions and materials conform to ASTM A269/A270...

150# Cast Stainless Socket Weld Union - 316 Stainless castings conform to ASTM A351 ACI Grade CF8 (304) & ACI Grade CF8M (316) CMTR's available upon request Stainless weld fitting dimensions...

150# Cast Stainless Socket Weld Union - 304 Stainless castings conform to ASTM A351 ACI Grade CF8 (304) & ACI Grade CF8M (316) CMTR's available upon request Manufacturing facility is ISO...

Stainless Steel Hex Nipple - Straight Sizes & Reducing Sizes Stainless castings conform to ASTM A351 ACI Grade CF8 (304) & ACI Grade CF8M (316) NPT threads conform to ASME B1.20.1...