Pipe Hangers and Supports

Fig. 279S Pipe Roll Stand - Plain Steel Finish Empire Fig. 279S Pipe Roll Stand Submittal PDF Pipe Chart: Common Diameters & Wall Thicknesses PDF

264 Adjustable Pipe Saddle Support Stanchion type support where vertical adjustment of stationary pipe is required. Complete Set Size Range: 2-1/2" through 36" Product Submittal / Data Sheet PDF Anvil Pipe Hangers & Supports Submittal Catalog PDF

133 Standard Duty Beam Clamp Clamp centers the load on beam to prevent distortion Note: Spacer is furnished for use with Fig. 290 weldless eye nuts. Spacer may be removed for use with Fig 278 eye rods. Plain or Hot-Dip Galvanized with Zinc Plated...

258 Pipe Saddle Support Stanchion type support for stationary pipe. Sizes 4" through 12" are Cast Iron. Sizes 14" through 36" are Carbon Steel. Sizes 4" through 12" are available in Carbon Steel by special request only. Plain or Zinc Plated (Hot-Dip...

Fig. 1900 1" Pipe Covering Protection Saddle Designed for use on insulated high temperature pipe lines to protect insulation from damage and minimize heat loss. Plain Steel Finish Empire Figure 1900 1" Pipe Covering Protection Saddle Submittal PDF Pipe...

93 Universal C-type Clamp Wide Throat Recommended for use under roof installations with bar joist type constructions, or for attachment to the top or bottom flange of structural shapes where the vertical hanger rod is required to be offset from the edge...

Fig. 427 Adjustable Pipe Saddle Support With U-Bolt Finish: Plain Steel Empire Figure 427 – Adjustable Pipe Saddle Support with U-Bolt Submittal PDF Pipe Chart: Common Diameters & Wall Thicknesses PDF

Fig. 73 Drop In Anchor Electro-Galvanized Empire Figure 73 Drop In Anchor Submittal PDF

1" Back of Stud HAP Pipe Hanger - Model PL-1111-B1  Fits: 1" CPVC, PEX, Copper and 3/4" PVC Pipe  The innovative – hold and protect – hap system pipe hanger is designed to securely hold 1” CPVC, PEX, copper pipe and 3/4″...

1-1/2" Back of Stud HAP Pipe Hanger - Model PL-1111-B10 Fits: 1-1/2" PVC and 2" Copper Pipe The innovative – hold and protect – hap system pipe hanger is designed to securely hold 1-1/2” PVC and 2″ copper pipe. This...

1-1/2" HAP Pipe Hanger - Model PL-1111-15 Fits: 1-1/2" PVC and 2" Copper Pipe The innovative – hold and protect – hap system pipe hanger is designed to securely hold 1-1/2” PVC pipe and 2” copper pipe. This easy-to-install hanger...

1-1/2" x 3" HAP Stud Guard - Model PL-1111-SNP1 The 1-1/2″ x 3″ stud guard is easy-to-install with just a cordless drill. These hap system stud guards are designed to help protect wiring and pipes from nails or screws and has a durable...

1-1/2" x 5" HAP Stud Guard - Model PL-1111-SNP10 The 1-1/2″ x 5″ stud guard is easy-to-install with just a cordless drill. These hap system stud guards are designed to help protect wiring and pipes from nails or screws and has a durable...

1-1/4" Back of Stud Hap Pipe Hanger - Model PL-1111-B5 Fits: 1-1/4" PVC and 1-1/2" Copper Pipe The innovative – hold and protect – hap system pipe hanger is designed to securely hold 1-1/4” PVC pipe and 1-1/2″ copper pipe. This...

134 Heavy Duty Beam Clamp Clamp centers the load on beam to prevent distortion. Two half-clamps, pipe spacer and bolt with nut assembled. Note: Spacer is furnished for use with Fig. 290 weldless eye nuts. Spacer may be removed for use with Fig 278 eye...

171 Single Pipe Roll For suspension of pipe from two rods where longitudinal expansion and contraction may occur. Size Range: 1" through 30" Cast Iron Roll and Sockets, Steel Roll Rod Product Submittal / Data Sheet PDF Anvil Pipe Hangers & Supports...

181 Adjustable Steel Yoke Pipe Roll For suspension of pipe from a single rod where longitudinal movement may occur because of expansion or contraction.  Size Range: 2-1/2" through 24" Cast Iron Roll, Carbon Steel Yoke, Roll Rod and Hex Nuts Product...

192 Adjustable Pipe Saddle Support Stanchion type support for stationary pipe where vertical adjustment is required. Size Range: 2" through 12" Product Submittal / Data Sheet PDF Anvil Pipe Hangers & Supports Submittal Catalog PDF

226 Truss Bracket or installation on the top chord of a steel web joist. Web thickness must be between 3/16" and 3/8" thick. Joist must be between 5" and 7" wide. For installation with Anvil Fig 202, 206, 207, & 551 brackets Rod Size 1/2" Material...

265 Adjustable Pipe Saddle Support With U-Bolt Stanchion type support where vertical adjustment is required, plus the additional stability provided by U-bolt attachment to pipe. Cast iron saddle, steel yoke and nuts, steel locknut nipple and special cast...

3" HAP Pipe Hanger - Model PL-1111-40 Fits: 4" PVC, Copper, Stainless, Black and Galvanized Pipe The innovative – hold and protect – hap system pipe hanger is designed to securely hold 4” PVC, copper, stainless and black pipe. This...

395 Cast Iron Ceiling Plate Gives finished appearance where pipe enters ceiling. Sizes 1/2" to 4" furnished with one machine screw; sizes 5" to 8", two machine screws. Sizes 1/2" through 8" Material Cast Iron Plain or Zinc Plated Product Submittal /...

610 Ceiling Plate 3/8" Ceiling plate mounts on the underside of wood or steel to support up to 2" NPS horizontal piping.  Installation: Mount on the underside of wood or steel using the fasteners listed in NFPA 13, the fasteners detailed in the...

65 Light Adjustable Clevis Hanger Recommended for suspension of stationary pipe or conduit. An economical attachment for light duty service. Product Submittal / Data Sheet PDF Anvil Pipe Hangers & Supports Submittal Catalog PDF Pipe Chart: Common...

86 C-Clamp w/ Set Screw & Lock Nut Recommended for attachment to “W” and “M” beams where thickness of flange Z does not exceed 0.75". When clamp is used with Fig. 89 retaining clip, flange thickness may not exceed 0.62"...

95 C-Clamp w/ Locknut Designed for fastening flange of “W” and “M” beam. Bottom hole tapped to accommodate hanger rod. Plain or Zinc Plated Product Submittal / Data Sheet PDF Anvil Pipe Hangers & Supports Submittal Catalog...

Clevis Hanger with Insulation Saddle System 260 ISS Recommended for the suspension of stationary insulated chilled or hotwater pipe lines.  V-Block design cradles pipe through out the entire erection process. Clevis bolt spacer included as standard...

Clevis Hanger with Insulation Saddle System 260R ISS Recommended for the suspension of stationary insulated chilled or hotwater pipe lines.  V-Block design cradles pipe through out the entire erection process. Clevis bolt spacer included as standard...

CT-65 Light Adjustable Clevis Hanger Copper Plated Recommended for suspension of non-insulated, stationary copper tube. Adjustment may be made either before or after tubing is in place without temporary support of pipe. Hanger rod and nuts may be locked...

FIG 218 Malleable Beam Clamp w/o Extension Recommended for attachment to structural steel. Use in conjunction with beams where beam widths are from 2-3/8" minimum to 7" maximum and flange thickness does not exceed 0.60". Click here if you need the...

Fig. 180 Short Clip - Plain Steel Finish Empire Figure 180 Short Clip Submittal PDF Pipe Chart: Common Diameters & Wall Thicknesses PDF

Fig. 1902 2" Pipe Covering Protection Saddle Designed for use on insulated high temperature pipe lines to protect insulation from damage and minimize heat loss. Plain Steel Finish Empire Figure 1902 2" Pipe Covering Protection Saddle Submittal PDF Pipe...

Fig. 1905 4" Pipe Covering Protection Saddle Designed for use on insulated high temperature pipe lines to protect insulation from damage and minimize heat loss. Plain Steel Finish Empire Figure 1905 4" Pipe Covering Protection Saddle Submittal PDF Pipe...

Fig. 21R Retaining Strap - Plain Carbon Steel Empire’s 21R Retainting Strap is designed for use with figure FIG. 21, FIG. 21L (3/8”-3/4”) and FIG. 23L (3/8”and 1/2”) to eliminate movement of the beam...

Fig. 23L Malleable Iron C-Clamp With Locknut Empire’s 23L Malleable Iron C- Clamp is designed for attaching hanger rod to the bottom flange of a beam. Empire Figure 23L - Malleable Iron C-Clamp with Locknut Sumbittal PDF

Fig. 245 Stud Guard, Twist Points Designed to protect piping and electrical lines that pass though wood framing from damage due to penetration from drywall or other fasteners. Simple installation with a hammer. Finish Electro-Galvanized Carbon Steel...

3/8" Purlin Clamp w/Locknut Empire’s Fig. 24L Purlin Clamp is designed for attaching hanger rod to large-lip steel Purlin beams. Empire Figure 24L 3/8" Purlin Clamp Submittal PDF

Fig. 280S Adjustable Pipe Roll Stand Finish: Plain Steel Empire Figure 280S – Adjustable Pipe Roll Stand Submittal PDF Pipe Chart: Common Diameters & Wall Thicknesses PDF

Fig. 421 Adjustable Pipe Saddle Support With Threaded Coupling Finish: Plain Steel Empire Figure 421 – Ajustable Pipe Saddle Support with Threaded Coupling Submittal PDF Pipe Chart: Common Diameters & Wall Thicknesses PDF

Fig. 425 Pipe Saddle Support With U-Bolt Finish: Plain Steel Empire Figure 425 – Pipe Saddle Support Submittal PDF Pipe Chart: Common Diameters & Wall Thicknesses PDF