Pipe Hangers and Supports

Stainless Steel U-Bolt 1" through 8" NPS 316 Stainless Steel U-Bolt and four (4) hex nuts. Max Temperature: 450°F / 650°F Recommended for support, or guide of heavy loads; often employed in power, process plant and marine service. Product...

Fig. 1904 3" Pipe Covering Protection Saddle Designed for use on insulated high temperature pipe lines to protect insulation from damage and minimize heat loss. Plain Steel Finish Empire Figure 1904 3" Pipe Covering Protection Saddle Submittal PDF Pipe...

Light Duty DWVG Hanger 1-1/2" through 4" NPS Carbon Steel - Electro Galvanized Pipe hanger or restraint for DWV pipe. Allows for easy adjustability of elevation Perfect for use with ABS or PVC plastic DWV pipe Product Submittal / Data Sheet PDF Light...

175 Roller Chair For support of pipe where longitudinal movement due to expansion and contraction may occur, but where no vertical adjustment is required. Size Range: 2" through 30" Cast Iron Roll, Steel Chair, Roll Rod, Bolts and Hex Nuts Product...

Fig. 909 Forged Steel Clevis Empire Figure 909 Forged Steel Clevis Submittal PDF

Fig. 1903 2-1/2" Pipe Covering Protection Saddle Designed for use on insulated high temperature pipe lines to protect insulation from damage and minimize heat loss. Plain Steel Finish Empire Figure 1903 2-1/2" Pipe Covering Protection Saddle Submittal...

4" HAP Pipe Hanger - Model PL-1111-40 Fits: 4" PVC, Copper, Stainless, Black and Galvanized Pipe The innovative – hold and protect – hap system pipe hanger is designed to securely hold 4” PVC, copper, stainless and black pipe. This...

260 Adjustable Clevis Hanger Recommended for the suspension of stationary pipe lines. Design has yoke on outside of lower U-strap so yoke cannot slide toward center of bolt, thus bending of bolt is minimized. Sizes 5" and up have rod and two nuts instead...

Copper Tubing Riser Clamp 1/2" through 6" CTS Carbon Steel - Epoxy Coated Max Temperature: 450° F For the suspension of stationary Copper Tube Max Load: 1/2" - 2-1/2" 150 lbs. Max Load: 3" 200 lbs. Max Load: 4" 250 lbs. Max Load: 6" 480 lbs. Product...

Fig. 422U Plain Adjustable Pipe Support W/ U-Bolt - Plain Steel Designed to be used in conjunction with a standard pipe and flange at the base to suppor piping where an overhead supporting member is not available. The stem is threaded the full length...

Fig. 83 Spring Wing Toggle Designed to be used with threaded rod in hollow walls. Order with or without bolt Finish Electro-Galvanized Empire Figure 83 Spring wing toggle and bolt Submittal PDF

Fig. 310OD "Emlok" Adjustable Swivel Ring Hanger Stainless for OD Sizes Empire Figure 310SS – “Emlok” Adjustable Swivel Ring Hanger, Stainless Steel Submittal PDF

Fig. 422 Adjustable Pipe Support Finish: Plain Steel Empire Figure 422 – Ajustable Pipe Support Submittal PDF Pipe Chart: Common Diameters & Wall Thicknesses PDF

3/4" Back of Stud HAP Pipe Hanger - Model PL-1111-B3/4  Fits: 3/4" CPVC, PEX, Copper and 1/2" PVC Pipe  The innovative – hold and protect – hap system pipe hanger is designed to securely hold 3/4” CPVC, PEX, copper pipe and...

Stainless Steel Riser Clamp 1/2" through 12" 304 Stainless Steel Max Temperature: 650° F For support of stationary steel pipe risers or conduit Max Load: 1/2" - 2-1/2" 150 lbs. Max Load: 3" 200 lbs. Max Load: 4" 250 lbs. Max Load: 6" 480 lbs. Max...

1-1/4" HAP Pipe Hanger - Model PL-1111-7 Fits: 1-1/4" PVC and 1-1/2" Copper Pipe The innovative – hold and protect – hap system pipe hanger is designed to securely hold 1-1/4” PVC pipe and 1-1/2” copper pipe. This easy-to-install...

1/2" Back of Stud HAP Pipe Hanger - Model PL-1111-B1/2 Fits: 1/2" CPVC, PEX and Copper Pipe  The innovative – hold and protect – hap system pipe hanger is designed to securely hold 1/2” PVC, CPVC, copper pipe and PEX tubing. This...

1/2" HAP Pipe Hanger - Model PL-1111-1/2  Fits: 1/2" CPVC, PEX and Copper Pipe  The innovative – hold and protect – hap system pipe hanger is designed to securely hold 1/2” PVC pipe and PEX tubing. This easy-to-install hanger...

2" HAP Pipe Hanger - Model PL-1111-23 Fits: 2" PVC and 2-1/2" Copper Pipe The innovative – hold and protect – hap system pipe hanger is designed to securely hold 2” PVC pipe and 2-1/2” copper pipe. This easy-to-install hanger...

Fig. 1901 1-1/2" Pipe Covering Protection Saddle Designed for use on insulated high temperature pipe lines to protect insulation from damage and minimize heat loss. Plain Steel Finish Empire Figure 1901 1-1/2" Pipe Covering Protection Saddle Submittal...

6" HAP Pipe Hanger - Model PL-1111-60 Fits: 6" PVC, Copper, Stainless, Black and Galvanized Pipe The innovative – hold and protect – hap system pipe hanger is designed to securely hold 6” PVC, copper, stainless and black pipe. This...

271 Pipe Roll Stand For support of pipe where longitudinal movement due to expansion and contraction may occur but where no vertical adjustment is required. Size Range: 2" through 42" Cast Iron Roll and Stand Product Submittal / Data Sheet PDF Anvil...

Fig. 600DIP Socket Clamp For Ductile Iron Pipe Size Empire Figure 600 – Socket Clamp Submittal PDF

261 Extension Pipe or Riser Clamp For support of stationary steel pipe risers, cast iron pipe or conduit. This product is not intended for use with hanger rods. For this application refer to Fig. 40 Riser Clamp. Clamp is fitted and bolted preferably...

Fig. 240 Stud Guard, Triangle Point Designed to protect piping and electrical lines that pass though wood framing from damage due to penetration from drywall or other fasteners. Simple installation with a hammer. Finish Electro-Galvanized Carbon Steel...

CT-128R Rod Threaded Ceiling Flange Recommended for attachment to wood beams or ceiling. Sizes 3/8" and 1/2" Material Malleable Iron Copper Plated Product Submittal / Data Sheet PDF Anvil Pipe Hangers & Supports Submittal Catalog PDF

Fig. 426 Adjustable Pipe Saddle Support Finish: Plain Steel Empire Figure 425 – Adjustable Pipe Saddle Support Submittal PDF Pipe Chart: Common Diameters & Wall Thicknesses PDF

14 Adjustable Side Beam Clamp Recommended for supporting pipe from the bottom flange of beams. Size 3/8" through 5/8" Plain or Zinc Plated Product Submittal / Data Sheet PDF Anvil Pipe Hangers & Supports Submittal Catalog PDF

92 Universal C-type Clamp, Standard Throat Recommended for use under roof installations with bar joist type construction, or for attachment to the top or bottom flange of structural shapes where the vertical hanger rod is required to be offset from the...

153 Pipe Hanger Flange Recommended for suspension of pipe lines or conduit from level ceilings. Flange size 3/8" has two holes, sizes 1/2", 5/8", and 3/4" have three holes. Provides vertical adjustment up to 1" Good Appearance Product Submittal / Data...

Fig. 430KTSF Adjustable Flange Support Kit - Hot Dipped Galvanized Empire Fig. 430KTSF Adjustable Flange Supoort Kit Submittal PDF Empire Fig. 428KT, 429KTU, 430KTSF, 431KTSF Installation Guide PDF 150# & 300# Flange Dimensional Specifications...

67 Pipe or Conduit Hanger Can be suspended by hanger rod or attached to wall. “T” slot in hanger permits side bolt to be installed after installation and setting of pipe. Strap and bolt with nut – assembled. Finish Zinc Plated Product...

Fig. 48 Riser Clamp for Plastic Pipe Empire’s Fig. 47 Riser Clamp for Plastic Pipe is designed for the support of vertical runs of plastic DWV pipe. Empire Figure 48 Riser Clamp for Plastic Pipe Submittal PDF

94 Wide Throat Top Beam Clamp The Anvil Wide Throat Top Beam Clamp has a ductile iron body with hardened steel cup point set screw and locknut. Clamps to bar joists or top flanges. UL Listed. Recommended for use under roof installations with bar joist...

CT-121 Copper Tubing Riser Clamp Recommended for support and steadying of copper tube risers, either insulated or non-insulated. This product is not intended for use with hanger rods. For support and steadying of copper tubing risers. Product Submittal...

Fig. 11F Flat Top Clevis Hanger Empire’s Fig. 11F Flat Top Clevis Hanger is designed for the suspension of non-insulated stationary pipe where space is limited. Stainless steel hangers are recommended for applications where protection from a...

Fig. 137C Plastic Coated Standard U-Bolt With 4 Hex Nuts Carbon steel U-Bolt and 4 finished hex nuts. Formed portion of the U-bolt is plastic coated. Recommended for support or guide for glass, copper, brass and aluminum pipe. Maximum Temperature:...

Fig. 420 Pipe Saddle Support Finish: Plain Steel Empire Figure 420 – Pipe Saddle Support Submittal PDF Pipe Chart: Common Diameters & Wall Thicknesses PDF

Fig. 51R Reducing Rod Coupling Electro-Galvanized Empire’s Fig. 51R Reducing Rod Coupling is designed for connecting two lengths of threaded rod with different diameters. Empire Figure 51R Reducing Rod Coupling Submittal PDF

259 Pipe Saddle Support With U-Bolt Cast iron stanchion saddle with steel yoke and nuts. 14" through 36" carbon steel saddle with steel yoke. 4" through 12" steel saddle available on special request. Stanchion type support with additional stability...